![topic](https://www.networkbulls.com/ask/public/images/2017-03-03-12-19-28-rip.jpg)
RIP
Questions 13
Answer 14
Views 70145
Do you have any Question?
Recommended
RIP Feed
RIp V2 with No Auto- Summary :
In Above Scenario : on R2 interfaces major network's is diifrent but st...
![author](https://www.networkbulls.com/ask/public/uploads/profile/118399238727111704813.jpg)
,
CCNA Routing and Switching
CCNA Routing and Switching
eigrp is advance distance router protocol , where as rip is distance vector
eigrp can use bandwidth , delay ,...
![author](https://www.networkbulls.com/ask/public/images/trainer/2017-03-17-06-17-25-mohit.jpg)
Master Trainer,
Dual CCIE #42145 (R&S, Security), CCSI #34989 and Data Center Written
Disadvantages of RIP :
1. In case of Rip hop count is used as a metric because of this Rip will always...
![author](https://www.networkbulls.com/ask/public/uploads/profile/118399238727111704813.jpg)
,
CCNA Routing and Switching
CCNA Routing and Switching
Diffrence between Rip v1 and v2 :
RIPv1 :
It is classfull.
It supports VLSM ( Variable length Subn...
![author](https://www.networkbulls.com/ask/public/uploads/profile/118399238727111704813.jpg)
,
CCNA Routing and Switching
CCNA Routing and Switching
Rip Load Balancing :
In above topology :
Configure Rip on all Four Routers :
R1(config)#router rip...
![author](https://www.networkbulls.com/ask/public/uploads/profile/118399238727111704813.jpg)
,
CCNA Routing and Switching
CCNA Routing and Switching
RIP V1 :
Rip v1 is classfull by default so it don't send subnet mask information with route updates.
...
![author](https://www.networkbulls.com/ask/public/uploads/profile/118399238727111704813.jpg)
,
CCNA Routing and Switching
CCNA Routing and Switching
Passive Interface In Rip :
Passive Interfaces : Through passive interfaces broadcast and multicast up...
![author](https://www.networkbulls.com/ask/public/uploads/profile/118399238727111704813.jpg)
,
CCNA Routing and Switching
CCNA Routing and Switching
t permits spoke-to-spoke route advertisement using neighbor command. That's it.
Let's look at this simple ...
![author](https://www.networkbulls.com/ask/public/images/trainer/2017-07-05-12-19-38-PiyushKataria (2).jpg)
Because rip uses UDP port 520 on layer 4.
![author](https://www.networkbulls.com/ask/public/uploads/profile/105743845457031330719.jpg)
,
ZAP
ZAP
When you are using ipv6 addresses while configuring RIP it is called as RIPng.
![author](https://www.networkbulls.com/ask/public/uploads/profile/118399238727111704813.jpg)
,
CCNA Routing and Switching
CCNA Routing and Switching
Assign ip addresses:-
Enable ipv6 unicast routing on both routers.
Enable RIP Process on both routers and then ...
![author](https://www.networkbulls.com/ask/public/images/trainer/2017-07-05-12-19-38-PiyushKataria (2).jpg)
Hi Tahir
Yes it is possible.
As you mentioned, if some network administrator using RIP and some other is using EI...
![author](https://www.networkbulls.com/ask/public/uploads/profile/101121013305695297625.jpg)
,
ZAP
ZAP